Vintageview WSBIG1 - Big Bottle Rack Manuel d'utilisateur télécharger pdf

WS-BIG1 contains:

WS-BIG1 Wall Mount

Wine Rack Instructions

Wine Master Cellars •10645 E 47th Ave, Denver, CO 80239 • phone: 866.650.1500 • fax: 866.650.1501

Please feel free to contact us regarding the assembly of this product.

Tools Needed:

Before starting, open all Packaging for the WS-BIG1 and take inventory to make sure you have everything.

• 1 Neck Strip

• 2 Plastic Couplers

• 1 Spirit Level

• 1 Marking Pen or Pencil

• 1 Tape Measure

• 1 Screwdriver

• Drill and Drill Bits (Necessary in Some Cases)

There are four pre-drilled mounting holes in each strip, eight total, per rack. Appropriate fasteners must be utilized in

every mounting hole for proper installation. Fasteners are not included with your WS-BIG1. However, we recommend the

following fasteners for these surfaces:

Fasteners:

• Wood Surface: #8 x 1-1/4” wood screw

• Drywall/Wallboard Surface: #8 x 1-1/4” screw with spiral inserts for the bottom two holes in each strip (4 total) and

an expanding hollow wall anchor such as a toggle bolt for the top hole in each strip (2 total)

• Concrete, Brick or Stucco: 3/16” x 1 ¾” masonry screw or #8 x 1 ¼” screw with appropriate size expanding anchor

NOTE: If you are attaching the WS-BIG1 to a custom Floor to Ceiling Frame (FCF) you will attach the units to the

FCF using the self-drilling screws included in the FCF packaging.

WS-BIG1 Installation Instructions

1 - Determine which direction the bottle necks

should point.

• 1 Base Strip

• 8 Rubber Mounting Hole Caps

1.1. If the bottle necks are to point to the right, the base

strip must be installed to the left of the neck strip.

1.2. If the bottle necks are to point to the left, the base

strip must be installed to the right of the neck strip.

2.1. The centerline of the rst strip (either base or neck

depending on bottle neck direction) should be at least 3

½” from adjacent walls or obstructions. This allows for the

bottle to overhang the rack (Fig. 1, Dim. A).

2.2. From centerline of the rst strip, measure 10-14” to

the centerline of the next strip. This dimension should be

tailored to the specic bottle size (3L to 6L) that will be

stored in the rack (Fig. 1, Dim. B).

2.3. (For multiple columns) Locate the centerline of the

next strip (Fig. 1, Dim. C) twice the measurement used for

Dim. A, approximately 7”, away from the prior strip. [Dim.

A X 2 = Dim. C]

2.4. (For multiple columns) Continue marking the center-

lines, alternating between Dim. B and Dim. C.

2 - Lay out the wall.

DIM. A

1 2

Résumé du contenu

Page 1 - Wine Rack Instructions

WS-BIG1 contains:WS-BIG1 Wall Mount Wine Rack InstructionsWine Master Cellars •10645 E 47th Ave, Denver, CO 80239 • phone: 866.650.1500 • fax: 866.65

Page 2 - Warranty

3.1. Reference the Fasteners section for recom-mended fastener types.3.2. Using a level, ensure that each strip is plumb prior to securing it to the

Commentaires sur ces manuels

Pas de commentaire

Vintageview WSBIG1 - Big Bottle Rack Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Équipement Vintageview WSBIG1 - Big Bottle Rack. VintageView WSBIG1 - Big Bottle Rack User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Équipement Vintageview WSBIG1 - Big Bottle Rack